In this article below you can get a good deal of helpful details all about How to Install a Bathtub.
Installing a tub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate speedily; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job as well as fit trying it. Instead of working with a contractor to take over a halfway-completed job, it is far better to think about using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bathtub in your restroom if you have currently gotten a brand-new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools as well as material checklist ought to make up the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Safeguard the faucet in place with the supplier given backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet ports. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Using both wooden boards under its feet, place the bath tub in the required placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the tub until the level reads degree.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the appropriate supply pipe by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system and also inspect all joints and also new pipework for leakages and tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will certainly resolve it into its final placement.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split a stiff seal, creating the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack fairly very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly readily available on the market. It is advisable to fit the tiles making use of water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very serious about Installing A Bathtub and I am praying you enjoyed my piece. In case you enjoyed reading our page please be sure to share it. I love reading our article about How to Install a Bathtub Yourself.
Schedule Service Pickup